They’re Built Tough!
They Look Great!
Printable Brochures at the bottom of page
Most companies DO NOT offer As thick of a Firebox, Color options, Extra insulation, 235 gallon Water Capacity, and a conservative 235,000 BTU’s OR 340 gallon and 340,000 BTU’s with a Separate Ash Removal Door, without making you up-size, if they even offer it at all.
Acme furnace Model 235 $4500
We make our 235 furnace that is compatible with most Household and Shop applications 5500 sq. ft calculated on 8 ft. ceilings. This Model has a 34 x 36 x 26 fire box and hold 235 gallons of water.
The 235 Furnace measures 5W x 6L x 8T and weighs 1800 lb. before water. There is a 10 inch tall ash compartment with a separate door for easy ash removal and a better burn. This model again will heat 5500 sq ft. so there is no need to up size to heat your home and shop/garage.
Acme Furnace Model 340 $5400
Next up is Our larger unit our 340 model that will heat large homes and large buildings 8500 sq ft. (calculated on 8 ft ceilings also). The Acme 340 has a 48 x 36 x 26 firebox with the 10 inch tall ash compartment and holds 340 gallons of water.
This unit measures 85″L X 5′ W X 8′ T and weighs 2200 lb. before water This Furnace is great for heating larger homes along with other out buildings or for commercial use.
Acme Furnace Model 735 $9150
This is Our largest unit the 735 Model it is used for Commercial buildings, warehouses and multi-home heating. Our 735 features a door that is a whopping 36″ x 44″ and Water Cooled..this door is big enough to fit a wood pallet in. The firebox on the 735 measures 5 ft. deep and 5 ft. wide and is designed using 3/8″ steel, it measures 81″ W x 85″ L x 10’T and weighs 5000 lb. before water. The 735 also has an ash compartment with separate door and a super heavy grates for a complete burn. We have also added Dual blowers to create TURBULENCE for a hotter, more even burn. This unit has a heavy 3/16″ thick water jacket holding 735 gallons of water, producing up to 735,000 BTU. The water than completely surrounds the firebox and ash compartment to extract the most heat possible, it even surrounds the flue pipe. The flue pipe extends two feet down into the firebox in the back to hold the heat and gases for a total burn. The separate ash door makes ash removal a much easier task.
Our Furnaces are NOT Pressurized!! Each Furnace has an over flow pipe that extends out the back of the Furnace!
All of these features still allow us to keep our quality and our high standards. We still concentrate on building the best, most reasonable priced furnace available. Compare prices and features before you purchase your furnace. What you want is a furnace that will last for years and be easy to maintain. We have that quality in our
Our furnaces also have a thermostat controlled draft blower that blows in from the back and through the ash pan under the fire not through the door and over the fire. We then double insulate the furnace and cover it with 40 year warranted steel siding and trim, and will build in almost any color. These furnaces are rated at 235,000 BTU and will heat 5500 sq.ft.in the very cold climate or 340,000 BTU and 8000 sq.ft.. They will heat your Home, Shop, Hot Water and your Hot-tub if you want. One pump is included but there are hookups for another and we will add more if needed. Just make sure to request more pumps to be added when placing your order! Our small furnace weighs 1800+ lbs. without the water. We have a 20 year burnout warranty and would be proud to show you the quality material and workmanship before you buy. With Acme Furnaces you can select your colors for the roof, siding and trim at no extra charge just let us know your selection when ordering!
Things to Compare When Looking For an Outdoor Furnace
Ours Furnaces have 6″ insulated sides, front,back and bottom. The top has 12″, PLUS the double bubble reflective covering we use also.. Not every company insulates the bottom.
Ash Removal Made Easy
We have a 10″ tall compartment on the 235 &340 with grates to insure a total burn and ease of ash removal, no need to let the fire burn down and scoop to side to remove ash.
Greater Water Capacity
Our 235 Acme Furnaces have a 235 gallon capacity giving you more BTUs for your money. Our 340 Furnace 340 gallons and the Acme 735 hold 735 gallons. A BTU is the amount of heat it takes to raise the temperature of a pound of water by one degree. BTU’s Explained
If you start with 55 degree water and you raise it to 180 degrees this is a 125 degree change.
Water weight 8 lbs. per gallon.
235 gal. x 8 lbs. = 1880 lbs.
1880 lbs. x 125 degrees = 235,000 BTUs
Don’t be fooled, this is a proven fact you would have to heat 100 gallons of water to 435 degrees to extract 300,000 BTUs. That’s not possible or even smart to try!
It Just Makes Sense
Wood is still the most renewable resource we have and the only one you can control the cost of.
A truck load of wood on average is equal to just over 100 gallon of propane when burnt through our controlled furnace meaning at today’s prices a truck load of wood is equal to $250-$350. Propane and Electric heat prices have no end in sight.
This alone will save much more than the price of the Furnace plus you heat your hot water for FREE saving you another $30-$60 per month.
Acme Furnace’s are an Easy Installation
Outside Back of the Acme Furnace
Inside the Home or Building with a Hotwater Sidearm
We recommend a seperate Heat Only Thermostat to Control Our Outdoor Furnace
Using the exisiting thermostat(4 wires) and then adding a second heat only thermostat (2 wires, power wire and fan wire) connected so only the fan comes on with use of your outdoor wood furnace. When the 2 wire thermostat determines it’s time too heat the building it calls for the fan to come on and distribute the hot air from the heat exchanger.
Our Furnaces can be installed by any Heat and Cooling Company or like minded person. Having a concrete pad for your furnace is recommended. Trenching from the furnace to the build for the pipe is usually done with a small bucket excavator or ditch witch, digging down 30 to 36 inches is recommend. Connecting the heat exchangers and the lines to the back of the furnaces is where the Heating and Cooling folks come in. Just making sure to get your supply and return line hooked up properly to the pump. Thermostat temperature control is added to set your preference for room temperature just like your forced air unit. A fresh water supply is need to fill and replenish the boiler with water. This can be done with a separate line to supply the fresh refill water to the boiler or by putting “T’ with a valve in the return line to the furnace to supply water to your boiler. If heating your shop/garage a heat exchanger can be boxed in with a squirrel cage with a thermostat and the result is very effective for a warm place to work without getting to fancy and expensive.
Where to Place Your Furnace
We recommend a concrete landing. This 235 Model is on a 10′ x 10′ x 3″ inch pad, it is positioned at the back of the slab where the piping comes out of the ground and connects to the Furnace using the back panel for access. We recommend at least a 5′ x 10′ for our customers, this allows you to stand on firm ground while loading your Acme Furnace. Distance from your structure may vary with Home Owners Insurance Policy. We recommend at least 25′ with the door facing away from the structure 40′-100′ is ideal. Our pumps will handle a greater distance with consideration of the head lift. If the head lift is greater then 19′ we would most want to work with you and decide weather or not to recommend a bigger pump and adjust the cost accordingly.
Trenching to lay Your Underground Insulated Pipe
Trench digging can be done with a ditch witch, small bucket excavator or even by hand in some cases. We recommend your underground piping be at the same depth as recommended for water lines in your area. In this picture the ditch is 30-36 inches.
Hot Water Coil
If needed we can install 50′ of 5/8 copper coil in your furnace to heat your Hot Tub, Pool or if you don’t want to use a Side-Arm heat exchanger for the hot water you can use the Domestic coil for this also. The Hot Water Coil (50 ft. of 5/8″) and fittings are an additional $125 and must be added at the time you place your order.
Acme Furnaces Are Built To Last
Acme Furnaces are built using 3/8 rolled plate steel for the Strongest firebox on the market. 10 Gurage Steel on the Water Jacket this makes it easy for Acme Furnace Company to offers a 20 year burn out Warranty. 100% 5 Year on Site repair! We come to you at NO Charge! Another Original Idea Acme Furnace Offers!
We offer the ash grates and a separate door for superior burn and ease of ash removal. Our forced air draft blower, installed in the bottom of the burn barrel at the back of the Furnace, blows the air up under the firebox for efficient and total burn control.
All our furnaces are leak tested, double insulated, and then covered with 40 year maintenance free steel siding for a long lasting high quality furnace like No other on the market!
Acme Furnaces weigh in at a whopping 1800+ lbs. for a Model 235, 2200+ lbs. for the Model 340 and 5000+ lbs on the 735 showing just how much steel we actually have in our furnace.
We lift Our Furnaces by the chimney…try that with competitor’s furnaces. In addition our furnaces are built Forklift ready for your convience also!
CUSTOMERS ARE RESPONSIBLE TO GET THEIR FURNACE OFF ALL FRIEGHT DELIVERED SHIPPING!!!!
PRINTABLE Information BELOW!
Download Our Installation and Operating Manual with the link below!
For those who can only Burn Coal in their area Your Manual Link is Below:
ACME FURNACE COMPANY PRINTABLE BROCHURE Links Below